Welche CD meinst du die Recovery CD??
Wenn ja diese geht nur auf meinen kaputten Laptop
Hier der Log
smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, smartmontools
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA family
Device Model: WDC WD3200BEVT-22ZCT0
Serial Number: WD-WXE408J8H136
Firmware Version: 11.01A11
User Capacity: 320,072,933,376 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Nov 16 17:03:15 2010 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 199 199 051 Pre-fail Always - 7668
3 Spin_Up_Time 0x0027 186 185 021 Pre-fail Always - 1683
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3078
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 051 Old_age Always - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 4709
10 Spin_Retry_Count 0x0033 100 099 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2018
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 265
193 Load_Cycle_Count 0x0032 189 189 000 Old_age Always - 34931
194 Temperature_Celsius 0x0022 119 088 000 Old_age Always - 28
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 198 198 000 Old_age Always - 135
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 9914 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9914 occurred at disk power-on lifetime: 4706 hours (196 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 2c 1e 6e 60
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 18 28 1e 6e 02 00 11:02:22.370 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:22.370 SET FEATURES [Enable write cache]
60 08 08 28 1e 6e 02 00 11:02:19.143 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:19.143 SET FEATURES [Enable write cache]
60 08 f0 28 1e 6e 02 00 11:02:15.773 READ FPDMA QUEUED
Error 9913 occurred at disk power-on lifetime: 4706 hours (196 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 2c 1e 6e 60
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 08 28 1e 6e 02 00 11:02:19.143 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:19.143 SET FEATURES [Enable write cache]
60 08 f0 28 1e 6e 02 00 11:02:15.773 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:15.773 SET FEATURES [Enable write cache]
60 08 e0 28 1e 6e 02 00 11:02:12.546 READ FPDMA QUEUED
Error 9912 occurred at disk power-on lifetime: 4706 hours (196 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 2c 1e 6e 60
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 f0 28 1e 6e 02 00 11:02:15.773 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:15.773 SET FEATURES [Enable write cache]
60 08 e0 28 1e 6e 02 00 11:02:12.546 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:12.546 SET FEATURES [Enable write cache]
60 08 d0 28 1e 6e 02 00 11:02:09.043 READ FPDMA QUEUED
Error 9911 occurred at disk power-on lifetime: 4706 hours (196 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 2c 1e 6e 60
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 e0 28 1e 6e 02 00 11:02:12.546 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:12.546 SET FEATURES [Enable write cache]
60 08 d0 28 1e 6e 02 00 11:02:09.043 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:09.043 SET FEATURES [Enable write cache]
60 08 c0 28 1e 6e 02 00 11:02:05.816 READ FPDMA QUEUED
Error 9910 occurred at disk power-on lifetime: 4706 hours (196 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 2c 1e 6e 60
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 d0 28 1e 6e 02 00 11:02:09.043 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:09.043 SET FEATURES [Enable write cache]
60 08 c0 28 1e 6e 02 00 11:02:05.816 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 11:02:05.816 SET FEATURES [Enable write cache]
60 08 b0 28 1e 6e 02 00 11:02:02.302 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.