Beiträge von mvm

    Hallo zusammen

    Vielen Dank für die Unterstützung bis jetzt :)

    Ich habe mal wieder eine Fall.
    Der PC startet sehr sehr langsam 20 - 30 min.

    Ich habe die hier genannte Software wieder zum Testen der festplatte genutzt. Bin mir aber nicht ganz sicher ob der Festplatte was fehlt.

    Vielleicht kann sich ja mal jemand die Auswertung Ansehen.

    Vielen Dank schon mal :)

    smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
    Copyright (C) 2002-10 by Bruce Allen, smartmontools

    === START OF INFORMATION SECTION ===
    Device Model: WDC WD3200BPVT-22ZEST0
    Serial Number: WD-WX81A70E2520
    Firmware Version: 01.01A01
    User Capacity: 320.072.933.376 bytes
    Device is: Not in smartctl database [for details use: -P showall]
    ATA Version is: 8
    ATA Standard is: Exact ATA specification draft version not indicated
    Local Time is: Tue Jun 4 19:01:27 2013 UTC
    SMART support is: Available - device has SMART capability.
    SMART support is: Enabled

    === START OF READ SMART DATA SECTION ===
    SMART overall-health self-assessment test result: PASSED

    General SMART Values:
    Offline data collection status: (0x00) Offline data collection activity
    was never started.
    Auto Offline Data Collection: Disabled.
    Self-test execution status: ( 0) The previous self-test routine completed
    without error or no self-test has ever
    been run.
    Total time to complete Offline
    data collection: (7380) seconds.
    Offline data collection
    capabilities: (0x7b) SMART execute Offline immediate.
    Auto Offline data collection on/off support.
    Suspend Offline collection upon new
    command.
    Offline surface scan supported.
    Self-test supported.
    Conveyance Self-test supported.
    Selective Self-test supported.
    SMART capabilities: (0x0003) Saves SMART data before entering
    power-saving mode.
    Supports SMART auto save timer.
    Error logging capability: (0x01) Error logging supported.
    General Purpose Logging supported.
    Short self-test routine
    recommended polling time: ( 2) minutes.
    Extended self-test routine
    recommended polling time: ( 88) minutes.
    Conveyance self-test routine
    recommended polling time: ( 5) minutes.
    SCT capabilities: (0x7035) SCT Status supported.
    SCT Feature Control supported.
    SCT Data Table supported.

    SMART Attributes Data Structure revision number: 16
    Vendor Specific SMART Attributes with Thresholds:
    ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
    1 Raw_Read_Error_Rate 0x002f 197 191 051 Pre-fail Always - 6092
    3 Spin_Up_Time 0x0027 152 136 021 Pre-fail Always - 1383
    4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2872
    5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
    7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
    9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 3683
    10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
    11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
    12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2740
    191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 12920
    192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 71
    193 Load_Cycle_Count 0x0032 185 185 000 Old_age Always - 46757
    194 Temperature_Celsius 0x0022 112 090 000 Old_age Always - 31
    196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
    197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 3
    198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
    199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
    200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0

    SMART Error Log Version: 1
    No Errors Logged

    SMART Self-test log structure revision number 1
    No self-tests have been logged. [To run self-tests, use: smartctl -t]


    SMART Selective self-test log data structure revision number 1
    SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
    1 0 0 Not_testing
    2 0 0 Not_testing
    3 0 0 Not_testing
    4 0 0 Not_testing
    5 0 0 Not_testing
    Selective self-test flags (0x0):
    After scanning selected spans, do NOT read-scan remainder of disk.
    If Selective self-test is pending on power-up, resume after 0 minute delay.

    Hallo ich habe da mal eine andere Festplatte. Hier die log Datei
    Vielleicht kann mir jemand sagen was der Platte fehlt danke
    smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
    Copyright (C) 2002-10 by Bruce Allen, smartmontools

    === START OF INFORMATION SECTION ===
    Model Family: ****IBM Deskstar 40GV & 75GXP series (all other firmware)
    Device Model: ****IBM-DTLA-307030
    Serial Number: ***YKEYKTVN011
    Firmware Version: TX4OA60A
    User Capacity: ***30,738,677,760 bytes
    Device is: *******In smartctl database [for details use: -P show]
    ATA Version is: **5
    ATA Standard is: *ATA/ATAPI-5 T13 1321D revision 1
    Local Time is: ***Thu Sep 15 17:37:30 2011 UTC

    ==> WARNING: IBM Deskstar 40GV and 75GXP drives may need upgraded SMART firmware.
    Please see http://www.geocities.com/dtla_update/ and
    Lenovo Support - Home (US)

    SMART support is: Available - device has SMART capability.
    SMART support is: Enabled

    === START OF READ SMART DATA SECTION ===
    SMART overall-health self-assessment test result: PASSED

    General SMART Values:
    Offline data collection status: *(0x00) * *Offline data collection activity
    * * * * * * * * * *was never started.
    * * * * * * * * * *Auto Offline Data Collection: Disabled.
    Self-test execution status: *****( **0) * *The previous self-test routine completed
    * * * * * * * * * *without error or no self-test has ever
    * * * * * * * * * *been run.
    Total time to complete Offline
    data collection: * * * * (1762) seconds.
    Offline data collection
    capabilities: * * * * * * (0x1b) SMART execute Offline immediate.
    * * * * * * * * * *Auto Offline data collection on/off support.
    * * * * * * * * * *Suspend Offline collection upon new
    * * * * * * * * * *command.
    * * * * * * * * * *Offline surface scan supported.
    * * * * * * * * * *Self-test supported.
    * * * * * * * * * *No Conveyance Self-test supported.
    * * * * * * * * * *No Selective Self-test supported.
    SMART capabilities: ***********(0x0003) * *Saves SMART data before entering
    * * * * * * * * * *power-saving mode.
    * * * * * * * * * *Supports SMART auto save timer.
    Error logging capability: *******(0x01) * *Error logging supported.
    * * * * * * * * * *No General Purpose Logging support.
    Short self-test routine
    recommended polling time: * * ( **2) minutes.
    Extended self-test routine
    recommended polling time: * * ( *19) minutes.

    SMART Attributes Data Structure revision number: 16
    Vendor Specific SMART Attributes with Thresholds:
    ID# ATTRIBUTE_NAME *********FLAG ****VALUE WORST THRESH TYPE *****UPDATED *WHEN_FAILED RAW_VALUE
    *1 Raw_Read_Error_Rate ****0x000b **078 **078 **060 ***Pre-fail *Always ******- ******19202677
    *2 Throughput_Performance *0x0005 **100 **100 **050 ***Pre-fail *Offline *****- ******0
    *3 Spin_Up_Time ***********0x0007 **100 **100 **024 ***Pre-fail *Always ******- ******215 (Average 223)
    *4 Start_Stop_Count *******0x0012 **099 **099 **000 ***Old_age **Always ******- ******4797
    *5 Reallocated_Sector_Ct **0x0033 **100 **100 **005 ***Pre-fail *Always ******- ******128
    *7 Seek_Error_Rate ********0x000b **100 **100 **067 ***Pre-fail *Always ******- ******0
    *8 Seek_Time_Performance **0x0005 **100 **100 **020 ***Pre-fail *Offline *****- ******0
    *9 Power_On_Hours *********0x0012 **098 **098 **000 ***Old_age **Always ******- ******16283
    10 Spin_Retry_Count *******0x0013 **100 **100 **060 ***Pre-fail *Always ******- ******0
    12 Power_Cycle_Count ******0x0032 **099 **099 **000 ***Old_age **Always ******- ******4734
    192 Power-Off_Retract_Count 0x0032 **097 **097 **050 ***Old_age **Always ******- ******4797
    193 Load_Cycle_Count *******0x0012 **097 **097 **050 ***Old_age **Always ******- ******4797
    194 Temperature_Celsius ****0x0002 **137 **137 **000 ***Old_age **Always ******- ******40
    196 Reallocated_Event_Count 0x0032 **094 **094 **000 ***Old_age **Always ******- ******268
    197 Current_Pending_Sector *0x0022 **100 **100 **000 ***Old_age **Always ******- ******58
    198 Offline_Uncorrectable **0x0008 **100 **100 **000 ***Old_age **Offline *****- ******0
    199 UDMA_CRC_Error_Count ***0x000a **200 **200 **000 ***Old_age **Always ******- ******0

    SMART Error Log Version: 1
    ATA Error Count: 2980 (device log contains only the most recent five errors)
    * *CR = Command Register [HEX]
    * *FR = Features Register [HEX]
    * *SC = Sector Count Register [HEX]
    * *SN = Sector Number Register [HEX]
    * *CL = Cylinder Low Register [HEX]
    * *CH = Cylinder High Register [HEX]
    * *DH = Device/Head Register [HEX]
    * *DC = Device Command Register [HEX]
    * *ER = Error register [HEX]
    * *ST = Status register [HEX]
    Powered_Up_Time is measured from power on, and printed as
    DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
    SS=sec, and sss=millisec. It "wraps" after 49.710 days.

    Error 2980 occurred at disk power-on lifetime: 16282 hours (678 days + 10 hours)
    *When the command that caused the error occurred, the device was active or idle.

    *After command completion occurred, registers were:
    *ER ST SC SN CL CH DH
    *-- -- -- -- -- -- --
    *40 59 08 0f 44 60 e0 *Error: UNC at LBA = 0x0060440f = 6308879

    *Commands leading to the command that caused the error were:
    *CR FR SC SN CL CH DH DC **Powered_Up_Time *Command/Feature_Name
    *-- -- -- -- -- -- -- -- *---------------- *--------------------
    *20 00 08 0f 44 60 e0 00 *****01:00:11.700 *READ SECTOR(S)
    *20 00 10 57 c8 f8 e0 00 *****01:00:11.700 *READ SECTOR(S)
    *20 00 08 47 74 5f e1 00 *****01:00:11.700 *READ SECTOR(S)
    *20 00 10 bf 81 1f e1 00 *****01:00:11.700 *READ SECTOR(S)
    *20 00 08 df 56 60 e1 00 *****01:00:11.700 *READ SECTOR(S)

    Error 2979 occurred at disk power-on lifetime: 16282 hours (678 days + 10 hours)
    *When the command that caused the error occurred, the device was active or idle.

    *After command completion occurred, registers were:
    *ER ST SC SN CL CH DH
    *-- -- -- -- -- -- --
    *40 59 08 d7 49 57 e0 *Error: UNC at LBA = 0x005749d7 = 5720535

    *Commands leading to the command that caused the error were:
    *CR FR SC SN CL CH DH DC **Powered_Up_Time *Command/Feature_Name
    *-- -- -- -- -- -- -- -- *---------------- *--------------------
    *20 00 08 d7 49 57 e0 00 *****01:00:00.600 *READ SECTOR(S)
    *20 00 2b ef ee 01 e2 00 *****01:00:00.600 *READ SECTOR(S)
    *20 00 08 9f 40 60 e0 00 *****01:00:00.600 *READ SECTOR(S)
    *20 00 0e b7 fa ff e1 00 *****01:00:00.600 *READ SECTOR(S)
    *20 00 08 7f fb f5 e1 00 *****01:00:00.600 *READ SECTOR(S)

    Error 2978 occurred at disk power-on lifetime: 16282 hours (678 days + 10 hours)
    *When the command that caused the error occurred, the device was active or idle.

    *After command completion occurred, registers were:
    *ER ST SC SN CL CH DH
    *-- -- -- -- -- -- --
    *40 59 08 97 4f 60 e0 *Error: UNC at LBA = 0x00604f97 = 6311831

    *Commands leading to the command that caused the error were:
    *CR FR SC SN CL CH DH DC **Powered_Up_Time *Command/Feature_Name
    *-- -- -- -- -- -- -- -- *---------------- *--------------------
    *c4 00 08 97 4f 60 e0 00 *****00:59:27.800 *READ MULTIPLE
    *c4 00 08 5f 09 08 e2 00 *****00:59:27.700 *READ MULTIPLE
    *c4 00 08 6f 09 08 e2 00 *****00:59:27.700 *READ MULTIPLE
    *c4 00 08 87 fd 07 e2 00 *****00:59:27.700 *READ MULTIPLE
    *c4 00 08 8f f0 07 e2 00 *****00:59:27.700 *READ MULTIPLE

    Error 2977 occurred at disk power-on lifetime: 16282 hours (678 days + 10 hours)
    *When the command that caused the error occurred, the device was active or idle.

    *After command completion occurred, registers were:
    *ER ST SC SN CL CH DH
    *-- -- -- -- -- -- --
    *40 59 30 6e 1d 69 e0 *Error: UNC at LBA = 0x00691d6e = 6888814

    *Commands leading to the command that caused the error were:
    *CR FR SC SN CL CH DH DC **Powered_Up_Time *Command/Feature_Name
    *-- -- -- -- -- -- -- -- *---------------- *--------------------
    *c4 00 80 1f 1d 69 e0 00 *****00:51:04.600 *READ MULTIPLE
    *e7 00 00 00 00 00 a0 00 *****00:51:04.600 *FLUSH CACHE
    *c5 00 08 47 00 5e e0 00 *****00:51:04.500 *WRITE MULTIPLE
    *c5 00 08 27 fc f5 e1 00 *****00:51:04.500 *WRITE MULTIPLE
    *c5 00 08 3f 00 5e e0 00 *****00:51:04.500 *WRITE MULTIPLE

    Error 2976 occurred at disk power-on lifetime: 16282 hours (678 days + 10 hours)
    *When the command that caused the error occurred, the device was active or idle.

    *After command completion occurred, registers were:
    *ER ST SC SN CL CH DH
    *-- -- -- -- -- -- --
    *40 59 08 d7 49 57 e0 *Error: UNC at LBA = 0x005749d7 = 5720535

    *Commands leading to the command that caused the error were:
    *CR FR SC SN CL CH DH DC **Powered_Up_Time *Command/Feature_Name
    *-- -- -- -- -- -- -- -- *---------------- *--------------------
    *20 00 08 d7 49 57 e0 00 *****00:44:28.700 *READ SECTOR(S)
    *30 00 08 17 11 f5 e1 00 *****00:44:28.700 *WRITE SECTOR(S)
    *e7 00 00 00 00 00 a0 00 *****00:44:28.700 *FLUSH CACHE
    *20 00 08 ff 0e 60 e0 00 *****00:44:28.700 *READ SECTOR(S)
    *e7 00 00 00 00 00 a0 00 *****00:44:28.600 *FLUSH CACHE

    SMART Self-test log structure revision number 1
    Num *Test_Description ***Status *****************Remaining *LifeTime(hours) *LBA_of_first_error
    # 1 *Short offline ******Completed without error ******00% ****16283 ********-

    Device does not support Selective Self Tests/Logging

    smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
    Copyright (C) 2002-10 by Bruce Allen, smartmontools

    === START OF INFORMATION SECTION ===
    Model Family: Seagate Momentus 5400.3 series
    Device Model: ST9160821AS
    Serial Number: 5MA57E19
    Firmware Version: 3.ALC
    User Capacity: 160.041.885.696 bytes
    Device is: In smartctl database [for details use: -P show]
    ATA Version is: 7
    ATA Standard is: Exact ATA specification draft version not indicated
    Local Time is: Sat Nov 20 00:41:03 2010 UTC
    SMART support is: Available - device has SMART capability.
    SMART support is: Enabled

    === START OF READ SMART DATA SECTION ===
    SMART overall-health self-assessment test result: PASSED

    General SMART Values:
    Offline data collection status: (0x82) Offline data collection activity
    was completed without error.
    Auto Offline Data Collection: Enabled.
    Self-test execution status: ( 0) The previous self-test routine completed
    without error or no self-test has ever
    been run.
    Total time to complete Offline
    data collection: ( 426) seconds.
    Offline data collection
    capabilities: (0x5b) SMART execute Offline immediate.
    Auto Offline data collection on/off support.
    Suspend Offline collection upon new
    command.
    Offline surface scan supported.
    Self-test supported.
    No Conveyance Self-test supported.
    Selective Self-test supported.
    SMART capabilities: (0x0003) Saves SMART data before entering
    power-saving mode.
    Supports SMART auto save timer.
    Error logging capability: (0x01) Error logging supported.
    No General Purpose Logging support.
    Short self-test routine
    recommended polling time: ( 1) minutes.
    Extended self-test routine
    recommended polling time: ( 111) minutes.
    SCT capabilities: (0x0001) SCT Status supported.

    SMART Attributes Data Structure revision number: 10
    Vendor Specific SMART Attributes with Thresholds:
    ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
    1 Raw_Read_Error_Rate 0x000f 100 253 006 Pre-fail Always - 0
    3 Spin_Up_Time 0x0003 100 099 000 Pre-fail Always - 0
    4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3167
    5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
    7 Seek_Error_Rate 0x000f 083 060 030 Pre-fail Always - 232661778
    9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2780
    10 Spin_Retry_Count 0x0013 100 100 034 Pre-fail Always - 0
    12 Power_Cycle_Count 0x0032 097 097 020 Old_age Always - 3150
    187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
    189 High_Fly_Writes 0x003a 094 094 000 Old_age Always - 6
    190 Airflow_Temperature_Cel 0x0022 061 048 045 Old_age Always - 39 (Lifetime Min/Max 38/43)
    192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1403
    193 Load_Cycle_Count 0x0032 071 071 000 Old_age Always - 58060
    194 Temperature_Celsius 0x0022 039 052 000 Old_age Always - 39 (0 9 0 0)
    195 Hardware_ECC_Recovered 0x001a 077 063 000 Old_age Always - 222703058
    197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always - 4294967295
    198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline - 4294967295
    199 UDMA_CRC_Error_Count 0x003e 200 199 000 Old_age Always - 489
    200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
    202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0

    SMART Error Log Version: 1
    ATA Error Count: 275 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
    Powered_Up_Time is measured from power on, and printed as
    DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
    SS=sec, and sss=millisec. It "wraps" after 49.710 days.

    Error 275 occurred at disk power-on lifetime: 1544 hours (64 days + 8 hours)
    When the command that caused the error occurred, the device was active or idle.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 fe 12 00 00 40 Error: ABRT

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    2f 00 01 10 00 00 40 00 00:26:39.656 READ LOG EXT
    60 08 08 00 00 00 00 00 00:26:39.646 READ FPDMA QUEUED
    60 08 08 00 00 00 00 00 00:26:39.635 READ FPDMA QUEUED
    60 08 08 00 00 00 00 00 00:26:39.604 READ FPDMA QUEUED
    60 08 08 00 00 00 00 00 00:26:39.595 READ FPDMA QUEUED

    Error 274 occurred at disk power-on lifetime: 1538 hours (64 days + 2 hours)
    When the command that caused the error occurred, the device was active or idle.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 fe 12 00 00 40 Error: ABRT

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    2f 00 01 10 00 00 40 00 01:53:45.674 READ LOG EXT
    60 08 08 00 00 00 00 00 01:53:45.672 READ FPDMA QUEUED
    60 80 80 00 00 00 00 00 01:53:45.670 READ FPDMA QUEUED
    60 80 80 00 00 00 00 ff 01:53:45.669 READ FPDMA QUEUED
    60 80 80 00 00 00 00 00 01:53:45.667 READ FPDMA QUEUED

    Error 273 occurred at disk power-on lifetime: 1538 hours (64 days + 2 hours)
    When the command that caused the error occurred, the device was active or idle.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 fe 12 00 00 40 Error: ABRT

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    2f 00 01 10 00 00 40 00 01:51:49.994 READ LOG EXT
    60 08 08 00 00 00 00 00 01:51:49.986 READ FPDMA QUEUED
    60 78 78 00 00 00 00 00 01:51:49.986 READ FPDMA QUEUED
    60 00 00 00 00 00 00 00 01:51:49.983 READ FPDMA QUEUED
    60 00 00 00 00 00 00 00 01:51:49.980 READ FPDMA QUEUED

    Error 272 occurred at disk power-on lifetime: 1538 hours (64 days + 2 hours)
    When the command that caused the error occurred, the device was active or idle.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 fe 12 00 00 40 Error: ABRT

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    2f 00 01 10 00 00 40 00 01:51:49.994 READ LOG EXT
    60 08 08 00 00 00 00 00 01:51:49.986 READ FPDMA QUEUED
    60 78 78 00 00 00 00 00 01:51:49.986 READ FPDMA QUEUED
    60 00 00 00 00 00 00 00 01:51:49.983 READ FPDMA QUEUED
    60 00 00 00 00 00 00 00 01:51:49.980 READ FPDMA QUEUED

    Error 271 occurred at disk power-on lifetime: 1538 hours (64 days + 2 hours)
    When the command that caused the error occurred, the device was active or idle.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 fe 12 00 00 40 Error: ABRT

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    2f 00 01 10 00 00 40 00 01:51:49.994 READ LOG EXT
    60 08 08 00 00 00 00 00 01:51:49.986 READ FPDMA QUEUED
    60 78 78 00 00 00 00 00 01:51:49.986 READ FPDMA QUEUED
    60 00 00 00 00 00 00 00 01:51:49.983 READ FPDMA QUEUED
    60 00 00 00 00 00 00 00 01:51:49.980 READ FPDMA QUEUED

    SMART Self-test log structure revision number 1

    SMART Selective self-test log data structure revision number 1
    SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
    1 0 0 Not_testing
    2 0 0 Not_testing
    3 0 0 Not_testing
    4 0 0 Not_testing
    5 0 0 Not_testing
    Selective self-test flags (0x0):
    After scanning selected spans, do NOT read-scan remainder of disk.
    If Selective self-test is pending on power-up, resume after 0 minute delay.

    Hallo

    Ich habe ein Notebook mit Win Vista 32-Bit.
    Ich habe meine Festplatte auf zwei paritionen
    Aufgeteilt und auf beiden ist Win Vista .
    Jetzt mein Problem
    Wenn ich es starte dauert es ca 15 min bis das runde
    Windows Logo kommt dann nach 4 min schwarzer Bildschirm und
    Es passiert nichts mehr. Es ist egal welches Vista ich starte
    Bei beiden das gleiche.
    Könnte das ein Hardware defekt sein?

    Hallo

    Ich habe einen PC mit Windows XP.
    Die Festplatte ist in 3 Partionen aufgeteilt.
    Auf der ersten ist WindowsXP und auf der zweiten auch.
    Jetzt habe ich das Probleme das ich XP was auf der ersten ist nicht mehr Starten kann, er fährt hoch und nach 1 min kommt ein Blauer Bildschirm. Der Bildschirm sagt auf das Windows was in der Registrierung fehlt.
    Jetzt habe ich mir gedacht Repariere ich einfach Windows mit der XP CD aber meine Problem ist das wenn ich von CD starte das mir nur die zweite Partion angezeigt wird.

    Ich kann von der XP Version die noch Funktioniert auf die andere Partion zugreifen.

    Hat jemand eine Lösung für mein Problem?

    Danke schon mal im Voraus

    Stellenweise über Kabel und über die Intigrierte WLAN Karte.

    Ich habe es versucht mit Kabel und ohne, jedes mal ohne Erfolg.

    Die einstellungen auf dem Rechner haben sich aus irgenteinen Grund verändert.

    Jetzt wollte ich die Verschlüsselung auf dem Rechner wieder so einstellen wie es bem Router ist. Aber da komt dánn immer die meldung

    Mindestens eine Änderung wurde nicht erfolgreich auf die Drahtloskonfiguration angewendet.

    Hallo

    Ich habe ein Fujitsu Siemens D9510 mit Intel Centrino2 2,4Ghz
    Ich habe Windows XP Pro Service Pack3.
    Und ein Intel Wifi Link 5300 AGN.

    Ich habe jetzt das Problem wenn ich die Einstellungen von meinem WLAN ändern will z.b. Verschlüsselung dann kommt wenn ich auf OK klicke folgende Meldung

    Mindestens eine Änderung wurde nicht erfolgreich auf die Drahtloskonfiguration angewendet.


    Kann mir jemand helfen was ich da machen kann.

    Danke

    Hallo zusammen

    Ich hoffe das forum ist das Richtige.

    Ich habe ein Siemens Field PG mit einem Intel Pentium M 1.6 Ghz Prozessor, 1GB Arbeitsspeicher und 60 GB Festplatte. Das Notebook ist ein bisschen langsam. Hat von euch jemand eine empfehlung was ich machen kann das es schneller wird(Hardware)?

    mvm

    Hallo ich habe eine HP PSC 2355 Drucker. Wollte gerade was in farbe drucken und dann kam die meldung auf dem Drucker Monitor "Die dreifarbige Druckerpatrone eignet sich nicht für diesen Drucker".
    Was kann ich jetzt tun? Die patrone ist seit dem Kauf in Dem Gerät und wurde auch noch nie entfernt?

    Danke schon mal im vorraus

    hallo wenn ich ein sicherheits kopie von einer dvd mit d v d ****** erstellen will bekomme ich bei 55% immer die fehler meldung
    Windows XP 5.1
    IA32
    WinAspi: -
    ahead WinASPI: File 'C:\Programme\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.68, size=160016 bytes, created 22.07.2004 17:33:44
    Nero API version: 6.3.1.20
    Using interface version: 6.3.1.4
    Installed in: C:\Programme\Ahead\Nero\
    Application: ahead\Nero - Burning Rom
    Recorder: <_NEC DVD+-RW ND-6500A> Version: 2.40 - HA 1 TA 0 - 6.3.1.20
    Adapter driver: <atapi> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ATAPI

    === Scsi-Device-Map ===
    DiskPeripheral : FUJITSU MHT2040AT atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : _NEC DVD+-RW ND-6500A atapi Port 1 ID 0 DMA: On

    === CDRom-Device-Map ===
    _NEC DVD+-RW ND-6500A D: CDRom0
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 70254592 (0) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 479MB (490864kB)
    Free physical memory: 88MB (90960kB)
    Memory in use : 81 %
    Uncached PFiles: 0x0
    Use Static Write Speed Table: 0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    18.1.2006
    NeroAPI
    18:17:06 #1 Phase 112 File APIProgress.cpp, Line 273
    DVD-Video files reallocation started

    18:17:06 #2 Phase 114 File APIProgress.cpp, Line 273
    DVD-Video files reallocation completed (no file modified)

    18:17:06 #3 Phase 111 File APIProgress.cpp, Line 273
    DVD-Video files sorted

    18:17:07 #4 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in EEPROM, command version 2

    18:17:07 #5 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in EEPROM, command version 2

    18:17:07 #6 Text 0 File Reader.cpp, Line 126
    Reader running

    18:17:07 #7 Text 0 File Writer.cpp, Line 124
    Writer _NEC DVD+-RW ND-6500A running

    18:17:07 #8 Text 0 File AudioCompilationImpl.cpp, Line 817
    DRM: StartDrmRecording(RealRec:1, ImageRec:0, Copies:1)
    DRM: Beginning burn process.

    18:17:07 #9 ISO9660GEN -11 File geniso.cpp, Line 3899
    First writeable address = 0 (0x00000000)

    18:17:09 #10 ISO9660GEN -11 File geniso.cpp, Line 3899
    First writeable address = 0 (0x00000000)

    18:17:09 #11 Text 0 File Burncd.cpp, Line 3173
    Turn on Disc-At-Once, using DVD media

    21:11:24 #12 Text 0 File DlgWaitCD.cpp, Line 247
    Last possible write address on media: 2295103 (510:01.28, 4482MB)
    Last address to be written: 2286111 (508:01.36, 4465MB)

    21:11:24 #13 Text 0 File DlgWaitCD.cpp, Line 259
    Write in overburning mode: NO

    21:11:24 #14 Text 0 File DlgWaitCD.cpp, Line 2162
    Recorder: _NEC DVD+-RW ND-6500A, Media type: DVD+R

    21:11:24 #15 Text 0 File DlgWaitCD.cpp, Line 420
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================
    Insert empty disc to write to.
    (Medium in drive: unknown. Medium required by compilation: DVD+R/RW; DVD-R/RW; DVD+R9 Double Layer.)

    21:11:24 #16 Text 0 File ThreadedTransferInterface.cpp, Line 813
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 (CTransferItem)
    2 indices, index0 (150) not provided
    original disc pos #0 + 2286112 (2286112) = #2286112/508:1.37
    relocatable, disc pos for caching/writing not required/required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286112 blocks [_NEC DVD+-RW ND-6500A]
    --------------------------------------------------------------

    21:11:24 #17 Text 0 File ThreadedTransferInterface.cpp, Line 984
    Prepare recorder [_NEC DVD+-RW ND-6500A] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681957376, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_RecDep_|_CtrlAdr_
    0 | lead-in | 0 | 0x00 | 0x41
    0 | 1 | 0 | 0x00 | 0x41
    0 | 1 | 1 | 0x00 | 0x41
    2286112 | lead-out | 1 | 0x00 | 0x41

    21:11:24 #18 Phase 24 File APIProgress.cpp, Line 273
    Caching of files started

    21:11:24 #19 Text 0 File Burncd.cpp, Line 4183
    Cache writing successful.

    21:11:24 #20 Phase 25 File APIProgress.cpp, Line 273
    Caching of files completed

    21:11:24 #21 Phase 36 File APIProgress.cpp, Line 273
    Burn process started at 2.4x (3.324 KB/s)

    21:11:24 #22 Text 0 File ThreadedTransferInterface.cpp, Line 2344
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    21:11:24 #23 SCSI -1066 File Cdrdrv.cpp, Line 1188
    SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x051E6000
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x24
    Sense Qual: 0x00
    CDB Data: 0xAD 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x08 0x04 0x00 0x00
    Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A
    0x00 0x00 0x00 0x00 0x24 0x00

    21:11:24 #24 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in EEPROM, command version 2

    21:11:24 #25 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in EEPROM, command version 2

    21:11:24 #26 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in EEPROM, command version 2

    21:11:24 #27 Text 0 File DVDR.cpp, Line 4661
    Drive: _NEC DVD+-RW ND-6500A
    Booktype request: DVD-ROM, write to RAM
    select Booktype setting from RAM

    21:11:24 #28 Text 0 File DVDPlusRW.cpp, Line 628
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    21:24:10 #29 TRANSFER -25 File Reader.cpp, Line 379
    Error reading data

    21:24:19 #30 Text 0 File ThreadedTransfer.cpp, Line 229
    all writers idle, stopping conversion

    21:25:11 #31 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in RAM, command version 2

    21:25:11 #32 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in RAM, command version 2

    21:25:11 #33 Text 0 File DVDR.cpp, Line 4661
    Drive: _NEC DVD+-RW ND-6500A
    Booktype request: DVD-ROM, write to RAM
    select Booktype setting from RAM

    21:25:11 #34 Phase 38 File APIProgress.cpp, Line 273
    Burn process failed at 2.4x (3.324 KB/s)

    21:25:11 #35 Text 0 File AudioCompilationImpl.cpp, Line 828
    DRM: DRM burn session terminated.

    21:25:11 #36 Text 0 File AudioCompilationImpl.cpp, Line 857
    DRM: Closing entire DRM handling. Bye.

    21:25:16 #37 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in RAM, command version 2

    21:25:16 #38 Text 0 File DVDR.cpp, Line 5367
    Booktype counter: 500, Booktype selected in RAM, command version 2

    Existing drivers:

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)